FUT028 RGBW LED Controller Kit with 2.4GHz Remote & Group Sync, 12-24V
Couldn't load pickup availability
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
The FUT028 is an RGBW LED controller kit with a dedicated white mode and automatic group synchronisation — linked controllers relay the remote signal and run in step, which is what lets one remote drive several runs across a large room without them drifting apart.
What This Kit Works With
- RGBW LED strip — 5 pads (V+, R, G, B, W)
- Common-anode constant-voltage tape at DC 12V or 24V
- 6A per channel and 10A total — 120-240W depending on supply voltage
- Several controllers in one group, synchronised from a single remote
Not compatible with: Addressable / pixel tape is not supported. If your strip is marked WS2812B, WS2811, WS2815 or SK6812, or has three pads (VCC / DAT / GND) with a chip on every LED, it needs an SPI controller instead.
Count the solder pads on the cut end of your strip. Two pads is single colour, three is tunable white, four is RGB, five is RGBW and six is RGB+CCT. A chip marking such as WS2812B means the strip is addressable and needs an SPI controller rather than a PWM one.
Kit or Separate Parts?
A kit is the simple route: matched controller and remote, already paired. Buying separately is possible — a bare E3-RF, PR5 or HR5 plus the C4 RGB+CCT remote — and it is worth doing when you want more output than this kit offers: the PR5 carries 20A and the HR5 30A, against 10–15A here.
Key Features
Automatic group synchronisation
Linked controllers relay the signal and run dynamic modes in step across a large space.
Dedicated white mode
Switch the white row on its own, separately from the colour channels.
16 million colours
Full colour wheel plus independent brightness and saturation.
IP20 rated housing
85 × 45 × 23 mm, for indoor dry locations.
2.4GHz RF, not infrared
Works through walls with no line of sight, up to 30m.
5-year warranty
Stated in the manufacturer specification.
Adding App and Voice Control Later
This kit is remote-controlled out of the box, with nothing on your network. If you later want phone and voice control — scenes, schedules, Alexa and Google Home — add the WL-Box2 2.4GHz gateway and the same controller joins the Tuya app without being replaced. One gateway covers every compatible 2.4GHz device in range, so you need one for the house rather than one per controller.
Technical Specifications
Controller
| Model | FUT028 |
|---|---|
| Product Name | RGBW LED Strip Controller (2.4GHz) |
| Input Voltage | DC 12-24V |
| Output Current | Max 6A / channel |
| Total Output | Max 10A |
| Output Power | 120-240W |
| Output Type | Constant voltage |
| Control Signal | 2.4GHz RF |
| Control Distance | 30m |
| IP Rating | IP20 |
| Working Temperature | -10°C to 40°C |
| Dimensions | 85 × 45 × 23 mm |
| Warranty | 5 years |
Included Remote
| Model | FUT028 remote |
|---|---|
| Operating Voltage | 3V (2 × AAA, not included) |
| Standby Power | <20μA |
| Transmitting Power | 6dBm |
| Control Signal | 2.4GHz |
| Dimensions | 100 × 52 × 20 mm |
Setup Notes
- Power off before wiring.
- Match the supply voltage to the strip — a 24V strip on a 12V supply looks dim, and a 12V strip on 24V will be damaged.
- These are common-anode outputs: the shared positive goes to V+, and each colour channel to its own terminal.
- Stay inside the rated output. Longer runs need a second supply with a repeater rather than a bigger controller.
- The remote needs 2 × AAA batteries, which are not included.
- Pair the remote to the controller on first use, following the pairing step in the manual — usually powering the controller off and on, then pressing a key on the remote within a few seconds.
Not Sure This Is the Right One?
- Pick the FUT027 RGBW kit if you do not need group sync — that kit is cheaper.
- Pick the FUT025 RGB kit if your strip is RGB, with no white row.
- Pick the FUT037SA+ RGB+CCT kit if your strip is RGB+CCT, with warm and cool white.
- Pick the PR5 5-in-1 controller (20A) if you want 20A and will choose your own remote.
Related
Pair a controller with the matching tape: single colour, tunable white, RGB & RGBW, COB and addressable strip. Everything else is in LED controllers.